Fundamental Plumber Tips for Installing a Bathtub
Fundamental Plumber Tips for Installing a Bathtub
Blog Article
What are your opinions about How to Install a Bathtub?
Mounting a bathtub isn't exactly brain surgery, but it does require strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably hard project. If the old tub is conveniently obtainable, the task can move rapidly; if you need to open up a wall to remove the old tub and place the new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as set in the brand-new one. Make sure you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed job, it is much better to consider using one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This post will certainly help you install a brand-new bathtub in your shower room if you have currently gotten a brand-new tub as well as do not require to alter the setup of your previous water supply pipelines.
Your devices and material checklist need to comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather bothersome due to the limited accessibility that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. Once the supply pipes have been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in area in between the tap and the sink. Protect the tap in place with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former type ought to be attached to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing the two wooden boards under its feet, place the tub in the required setting. The wooden boards are valuable in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the bath tub until the spirit level reads level.
To mount taps, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the supply of water and examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub and also inspect the overflow electrical outlet and the typical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub must wait until the bathtub has actually been utilized a minimum of when as this will certainly resolve it right into its final placement.
Preparing for the Installment
First of all, the sustaining framework provided with the bathroom must be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack an inflexible seal, triggering the water to permeate the wall surface between the bathroom as well as the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and also installations. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to enable the motion experienced when the bathtub remains in use. The sealer can split relatively very early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that write-up on Installing A Bathtub through an associate on another web blog. For those who enjoyed our blog posting please remember to pass it around. Thank you so much for your time invested reading it.
Best choice? Dial. Report this page